Notifications
Clear all
Topic starter
having some issue while installing the application server/jboss with the new
Centricity Server Configurator.
After validating database connection and then validating and adding the hostname for the JBoss server.
i click in validate & install.
the validation again goes without any issue, then the installation start and after about 5 to 7 minutes of running it stop and shows an red X mark in installation.
this is what my logs contains
I|8/27/2015 4:42:05 PM Starting Log
I|8/27/2015 4:42:05 PM Deleted : \\JBOSS0\C$\GEDeployment\Resources
I|8/27/2015 4:42:06 PM Deleted : \\JBOSS0\C$\GEDeployment\InstallScripts
I|8/27/2015 4:42:06 PM Deleted : \\JBOSS0\C$\GEDeployment\WI
I|8/27/2015 4:42:13 PM Deleted : \\JBOSS0\C$\GEDeployment\jboss-ews-2.0
I|8/27/2015 4:42:13 PM Deleted : \\JBOSS0\C$\GEDeployment\ServiceLayer
I|8/27/2015 4:42:14 PM Completed copying C:\CPS_12_Staging\ServerConfigurator\Resources to remote directory: \\JBOSS0\C$\GEDeployment\Resources
I|8/27/2015 4:42:15 PM Completed copying C:\CPS_12_Staging\ServerConfigurator\InstallScripts to remote directory: \\JBOSS0\C$\GEDeployment\InstallScripts
I|8/27/2015 4:42:28 PM Completed copying C:\CPS_12_Staging\ServerConfigurator\WI to remote directory: \\JBOSS0\C$\GEDeployment\WI
I|8/27/2015 4:42:56 PM Completed copying C:\CPS_12_Staging\ServerConfigurator\jboss-ews-2.0 to remote directory: \\JBOSS0\C$\GEDeployment\jboss-ews-2.0
I|8/27/2015 4:42:58 PM Completed copying C:\CPS_12_Staging\ServerConfigurator\ServiceLayer to remote directory: \\JBOSS0\C$\GEDeployment\ServiceLayer
I|8/27/2015 4:42:58 PM Completed copying folders. Total time : 00:00:53
Database Password cannot be blank
I|8/27/2015 4:43:00 PM Total Deployment Time : 00:00:55
Posted : August 27, 2015 10:37 am
Hi,
The log is reporting that there cannot be a blank database password at 4:42:58 pm. Try entering the data again check that password was input/accepted.
Posted : August 27, 2015 11:33 am
yes i was, but it was a single server install.
Posted : August 27, 2015 11:54 am
+1 to EMP's response above. Enter the creds and password. Even though Server Setup will let you pass through this without credentials, the Server Configurator needs them.
EDIT: SP10 installed in our test environment without issues. We are installing it into production tomorrow, 8/29/15.
Posted : August 28, 2015 2:01 am
Topic starter
Thanks for the reply, but non of that was the issue. Password was setup properly.
the issue is with the Server configurator, I just realized that it does not support special character.
everything after any kind of special character will be ignored.
Posted : August 28, 2015 4:38 am
Which field do you see this problem with special characters in? Thanks
Posted : August 28, 2015 4:57 am
Topic starter
Application username and password for the database.
does not support any kind of special character.like : @!#$%^&*()
so complex password is out of the question
Posted : August 28, 2015 5:02 am
Strange manifestation... We were able to use ours without issues and it contains a few special characters.
Posted : August 28, 2015 5:04 am
In my test environment I used appuser/appuser. There is a standard password used by a few GE techs which ends in '@1' which I expect to be problematic if this is the case. The only reason I didn't use it was because I would have had to look it up and after multiple jboss reinstalls it was just easier to go with appuser/appuser
Mike Zavolas
Tallahassee Neurological Clinic
Posted : September 2, 2015 9:34 am
Mike,
In my experience working as a consultant with several GE clients, I think there was more than just a few GE techs using this. 😉
Oy vey!
Posted : September 2, 2015 9:40 am
